![]() Pre-drill the holes if necessary, and then secure the bracket using two fasteners (not included). Place the PoE Mounting Bracket at the desired location and mark the two holes.Slide the PoE Mounting Bracket down to remove it from the Gigabit PoE Adapter.Connect the other end of the Power Cord to a power outlet. Connect the Power Cord to the power port on the adapter.Connect an Ethernet cable from your LAN to the Ethernet port labeled LAN on the adapter.Connect the other end of the Ethernet cable from the UniFi AP to the Ethernet port labeled POE on the Gigabit PoE Adapter.Connecting to a UniFi SwitchĬonnect the other end of the Ethernet cable from the UniFi AP directly to a PoE port on the UniFi Switch. The UniFi AP can be powered directly by a UniFi Switch or with the included Gigabit PoE Adapter. Connect the Ethernet cable to the Main port.Then feed the Ethernet cable through the 18 mm hole. Insert the Flat Head Screws through the Mounting Bracket, ceiling tile, and Ceiling Backing Plate.Use a 3 mm drill bit to drill the screw holes, and cut or drill the hole for the Ethernet cable feed.Note: 25 mm is the distance from the center of the bottom mounting hole to the center of the cable hole. Mark a hole approximately 18 mm in diameter for the Ethernet cable feed.Place the Ceiling Backing Plate in the center of the ceiling tile.Turn the UniFi AP clockwise until it locks into place and the Locking Tab fits securely into the Locking Notch. Ensure that the UniFi AP is firmly seated on the Mounting Bracket.Align the arrow on the UniFi AP with the arrow on the Locking Tab of the Mounting Bracket.If the feed is along the mounting surface, feed the cable through the Cable Feed of the UniFi AP. Secure the Mounting Bracket to the wall by inserting the Screws into the anchors. Insert the Screw Anchors into the 6 mm holes.Then feed the CAT5/6 cable through the hole. If your Ethernet cable feeds through the wall, then cut or drill a circle approximately 18 mm in diameter.Use a 6 mm drill bit to drill the mounting holes. Use a pencil to mark the four mounting holes.Position the Mounting Bracket at the desired location on the wall with the arrow pointing up.Perform the steps for the appropriate installation: Wall Mount The UniFi AP can be mounted on the wall or ceiling. Locking Tab During installation, the Locking Tab on the Mounting Bracket moves from the Initial Position to the Final Position, where the Locking Tab fits securely into the Locking Notch on the UniFi AP to help prevent theft. Press and hold the Reset button for more than five seconds.Ĭable Feed Use the Cable Feed slot to feed the Ethernet cable along the mounting surface. Press and release the Reset button quickly. Reset The Reset button serves two functions for the UniFi AP: Power can be provided by the Gigabit PoE Adapter (included) or Ubiquiti Networks UniFi Switch. Main This Gigabit Ethernet port is used to connect the power and should be connected to the LAN and DHCP server. (This is described further in the Mounting Bracket section.) Locking Notch The Locking Notch will be used with the Mounting Bracket to help secure the UniFi AP. Indicates the device is in an isolated state (all WLANs are brought down until an uplink is found). It will also display the location of the AP on the map. Indicates the device has been successfully integrated into a network and is working properly.Ĭontroller software, the AP will flash. This usually indicates that a process such as a firmware upgrade is taking place. A management station running the UniFi Controller software, located either on-site and connected to the same Layer-2 network, or off-site in a cloud or NOCĪll UniFi devices support off-site management controllers.įor setup details, see the User Guide on the website: /unifi Hardware Overview LEDįactory default, waiting to be integrated.ĭevice is busy do not touch or unplug it.A DHCP-enabled network (for the AP to obtain an IP address as well as for the wireless clients after deployment).UniFi Controller software v4.6 or higher (available at: /unifi).Web Browser: Mozilla Firefox, Google Chrome, or Microsoft Internet Explorer 8 (or above).Java Runtime Environment 1.6 (or above).Microsoft Windows 7/8, Mac OS X, or Linux.It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, indoor cabling requirements, and Dynamic Frequency Selection (DFS) requirements. TERMS OF USE: All Ethernet cabling runs must use CAT5 (or above). Optional: Drywall or keyhole saw (to cut 18 mm hole for Ethernet cable feed).Drill and drill bit (6 mm for wall-mounting or 3 mm for ceiling-mounting).Ubiquiti UniFi AP AC LITE (UAP-AC-LITE) Quick Start Guide
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |